ARP Omni

In this post

What the ARP Omni is

The ARP Omni is a string synthesizer with a built-in polyphonic synthesizer section and a bass section, made by ARP Instruments of Massachusetts from the mid-1970s. Its 49-note keyboard uses divide-down tone generation, so every key can sound at the same time. Its successor, the ARP Omni-2, is covered on this page too.

The first model is often called the Omni 1, and the later one appears as Omni-2 or Omni 2. This page on the ARP Omni synthesizer lists the specs from ARP’s service manuals, explains the string-machine and divide-down design, and places the Omni among the string machines of its time. It also covers the musicians who described using it, the Full Bucket Music Oxid plugin, demo videos and dated used prices.

In short
  • A 500 kHz master oscillator, one top octave divider chip and a bank of frequency dividers give all 49 keys their own pitch, so the string and synth sections play chords of any size.
  • Strings: polyphonic violin and viola, monophonic cello and bass on the lowest one and a half octaves, all through three delay-line phase shifters.
  • Synth: the same tones through one 24 dB per octave low-pass filter, one amplifier and one ADSR envelope shared by every key.
  • The Omni-2 adds a preset bass synth with a Staccato switch, a separate bass output and a Single Trigger switch, and weighs 39.5 lb instead of 33 lb.
  • On 10 November 2026 Reverb gave no used-price estimate; its six dated Omni sales from 2019 to 2026 ranged from €700 to €1,700.

ARP Omni and Omni-2 specs

The figures below come from ARP’s service manuals, the only factory specifications I found for either model: the Omni manual dated February 1977 and the Omni-2 manual dated July 1978. I didn’t read the owner’s manuals.

Feature ARP Omni (model 2480) ARP Omni-2 (models 2471, 2472, 2473, 2475)
Service manual February 1977, document 90020000 July 1978, document 90026
Maker ARP Instruments, Inc., Newton, Massachusetts ARP Instruments, Inc., Lexington, Massachusetts
Keyboard 49 notes (4 octaves), split for the bass voices one and a half octaves from the low end Same
Tone generation 500 kHz master oscillator, LSI top octave divider, frequency dividers (divide-down) Same
String voices Violin 4′ and viola 8′ polyphonic; cello 8′ and bass 16′ monophonic with low-note priority on the lowest one and a half octaves Same voices; cello and bass on the first 20 notes
String controls Attack, release Attack, release
String effect Three parallel phase shifters built from analog delay lines Three parallel delay-line phase shifters
Synth pitches and waveforms 4′ and 8′; sawtooth and dynamic pulse; Waveform Enhancement switch 4′ and 8′; sawtooth and dynamic pulse; Hollow Waveform switch
Synth filter One 4075 low-pass VCF, 24 dB per octave, with resonance Same
Synth envelope One ADSR for the filter and amplifier One ADSR, with a Single Trigger switch
LFO About 0.1 Hz to 20 Hz, routed to the filter LFO speed slider, routed to the filter
Bass voices Synthesizer bass 8′ and 16′ on keys 1 to 20, through the synth filter Own preset bass synth with a two-pole low-pass filter, 8′ and 16′, Staccato switch
Outputs XLR high level, 1/4-inch low level, separate synthesizer output Switchable high or low main output; separate synthesizer, strings and bass outputs
Interface Gate out, trigger out, accessory (VCF control) input Upper gate out, lower gate out, trigger out, VCF CV input
Pedals Filter pedal, sustain footswitch Filter pedal, volume control of all outputs except bass, sustain footswitch
Construction Aluminum chassis, solid walnut endblocks, glass-epoxy boards Steel chassis, leather endblocks, glass-epoxy boards
Weight 33 lb 39.5 lb
From ARP’s service manuals for the Omni (February 1977) and the Omni-2 (July 1978), sections 1 to 3. The LFO range and filter type come from the circuit descriptions in the same manuals.

Release year, original price and source conflicts

The launch year is usually given as 1975. Korg’s ARP history page dates the Omni to 1975 and the Omni 2 to 1977, and Music Technology’s 1993 A-Z of Analogue gives 1975 to about 1981. The earliest dated source I found is ARP’s own newsletter, ARPeggio Vol. 5 No. 2, copyright 1976. It reports that ARP had unveiled the Omni and introduced it to dealers at the recent meeting of the National Association of Music Merchants in Chicago. I found no 1975 document.

For the Omni-2, Music Technology gives about winter 1977/78 and Reverb’s product details 1977 to 1981 (1975 to 1977 for the Omni), while the Omni-2 service manual carries a July 1978 copyright.

Prices come from secondary copies. The Retro Synth Ads blog transcribes Contemporary Keyboard’s Spec Sheet from November/December 1976, which gave a list price of $2,250, and a review in Synapse from the same months that called the price $2,395. I couldn’t open either magazine myself. Music Technology gives £1,200 as the original UK price. I found no launch price for the Omni-2.

How the ARP Omni works: a divide-down string machine

The Omni is built like the string machines of its day, not like a synthesizer with a separate voice for each note. Both service manuals describe the same tone generator: a master oscillator at 500 kHz drives a large-scale integrated top octave divider, which produces the highest twelve tones of the instrument. Frequency dividers, CD4520 counter chips in the Omni manual, derive every lower pitch from those twelve. This is called divide-down tone generation.

The dividers put out square waves. The Omni shapes each one into a sawtooth by differentiating it with a capacitor and clipping the negative half with a diode. The Waveform Enhancement switch, renamed Hollow Waveform on the Omni-2, lets part of that negative half through for a hollow, square-like sound.

Keys, gates and polyphony

Each key contact is wired to a capacitor through a resistor. The capacitor normally sits at 0 volts, and pressing the key pulls it to -15 volts, which keys the transistor gating arrays that let that key’s tones through. The Omni has 10 of these TDA470 arrays, five for the 4′ pitches and five for the 8′ pitches, so every key opens two gates. The time the capacitor takes to recharge to 0 volts after release sets how long the note keeps sounding, and the release slider changes it.

Because every key has its own pitch from the dividers and its own gate, chords of any size sound at once. What the keys share is the processing after the gates: one amplifier for the strings, and one filter and one amplifier for the synth section. Describing the Omni-2 in 1979, Sound International called the synth part a pseudo-polyphonic section with only one VCF and VCA.

String section and chorus phaser

The summed tones pass through three parallel phase shifters. Each one is an analog delay line whose delay time follows a clock of typically 50 kHz. Each has its own low-frequency oscillator, which varies that clock, so the delay moves by up to 0.8 milliseconds, and the three outputs are added together. The Omni manual calls the phasers chiefly responsible for the orchestral string effects. A VCA after them sets the attack, while the release still comes from the per-key capacitors.

ARP’s 1976 newsletter called its string process asynchronous phase modulation. The Chorus Phaser button sends the synth section through the same three phasers as well and slows them down. The synth output then also appears on the string output.

Synthesizer section

The synth section takes the same gated tones at 4′ and 8′ and runs them through a single 4075 low-pass filter with a slope of 24 dB per octave and adjustable resonance, then through an amplifier. One ADSR envelope drives both, with sliders for how far the envelope, the LFO and a pedal or external voltage move the filter. The LFO runs from about 0.1 Hz to 20 Hz. This is subtractive synthesis applied to a whole chord at once.

Triggering differs between the models. Music Technology describes the original Omni as multiple-triggering: every new key restarts the shared envelope. The Omni-2 adds a Single Trigger switch, and its manual explains that it lets the strings be played without retriggering the synth envelope. Sound International listed the single and multiple trigger choice among the Omni-2’s extras.

Bass section

The lowest notes have their own monophonic bass with low-note priority. On the original Omni, the 8′ and 16′ bass voices run through the synth section’s filter, and the string section adds a monophonic cello and bass. The Omni-2 manual gives the bass its own preset synthesizer: a two-pole low-pass filter and envelope, an 8′ and 16′ voice taken from the dividers, a Staccato switch for a shorter decay, and a separate bass output.

Differences between the Omni and the Omni-2

The Omni-2 keeps the 500 kHz divide-down generator, the three-phaser string section and the 4075 filter, so its sound sources are the same. The changes are in the bass, the triggering and the connections. Its bass becomes a separate preset synth with Staccato, the synth section gains the Single Trigger switch, and the rear panel adds separate strings and bass outputs plus upper and lower gate outputs. The volume pedal input controls all outputs except the bass.

The case changed too. The Omni has an aluminum chassis with solid walnut endblocks and weighs 33 lb, while the Omni-2 has a steel chassis with leather endblocks and weighs 39.5 lb. Reverb’s product details list the Omni in black and the Omni-2 in black and orange.

History: from the String Ensemble to the Omni and the Quadra

ARP Instruments was founded in 1969 and named after Alan R. Pearlman, one of its founders. Before the Omni, ARP sold the String Ensemble, which Korg dates to 1974. Music Technology’s 1993 guide says ARP bought that keyboard in from Holland and put stickers over the Solina name.

The same 1976 newsletter that announced the Omni also explained ARP’s Polyphonic System. In it, Output 1 of a String Ensemble is patched into the Ext. Audio In jack of an ARP Axxe, so the polyphonic string tones are processed through the Axxe’s filter and amplifier. The Omni builds a string section and a shared filter and amplifier into one case. Sound International’s 1979 history of ARP describes the Omni-2 as descended from the String Ensemble and the Explorer monosynth.

ARP’s newsletter said the Omni cost approximately half as much as other polyphonic keyboard synthesizers. It named jazz keyboardist Les McCann as the first major artist to play it live, at Boston’s Jazz Workshop. In July 1977 an editorial in Polyphony magazine named the Polymoog, the Arp Omni and many string synthesizers as new instruments that manufacturers were advertising as polyphonic.

At the 1978 NAMM show, Sound International saw ARP’s next keyboard, the Quadra, and described it as a sort of cross between an Omni and an Odyssey. Its 1979 history says ARP hoped the Quadra would consolidate the stronghold the Omni had given the company in the polyphonic market. The Quadra added a lead synth and an arpeggiator. Korg’s history page says ARP closed in 1981, and Korg revived the ARP brand in 2015 with the Odyssey and reissued the ARP 2600 in 2020.

The Omni among the string machines of its time

When International Musician surveyed string machines in October 1975, the Solina retailed at about £550, and the field included the Elka Rhapsody, the Galanti Instastring with a built-in phase module and Roland’s RS-101. The Omni added a filtered synth section on top of its strings.

Other keyboards used the divide-down method as well. The Synapse review transcribed by Retro Synth Ads noted that, as in the Polymoog, all its frequencies came from top-octave division. Music Technology’s 1993 guide, in its entry for the Quadra, says the Quadra’s Omni section used a divide-down circuit like the Polymoog’s. Other makers built similar hybrids. Sound International found Roland’s new Paraphonic RS-505 similar to the ARP Omni at the 1978 NAMM show, and Electronics & Music Maker described the Korg Delta in July 1984 as a hybrid like the Omni, with separate outputs for its sections.

By March 1984 the Omni was a secondhand buy in Britain. Electronic Soundmaker & Computer Music printed approximate guide prices for string and ensemble keyboards. The chart below shows all 14 entries it priced.

String and ensemble keyboards: UK secondhand guide prices, March 1984
Bar length = the magazine’s approximate secondhand price on a scale of £0 to £500. The ARP Omni bar is green.
ARP Omni 1/II (synth/strings/bass)£400
Moog Opus 3 (strings/brass)£400
ARP Solina (strings/brass)£350
Roland 505 (paraphonic synth)£350
Godwin 849 (string synth)£300
Logan String Melody (strings/organ)£300
Yamaha SK20 (synth/strings/brass)£300
Welson Symphony (Rhapsody 610 clone)£275
Roland RS09 (organ/strings)£250
Roland SA09 (piano/organ)£250
Elka Rhapsody 610 (strings/piano/harpsichord)£250
ARP Quartet (strings/organ/piano/brass)£200
Logan Vocalist (voices)£175
Hohner K2 (strings)£150
From the price list in John Wright’s String Synths feature, Electronic Soundmaker & Computer Music, March 1984, which calls them very approximate guides. All 14 priced entries are shown; for the Elka Rhapsody the 610 price is used, and the magazine gives £150 for the 490. Welson Symphony is listed there as a Rhapsody 610 clone.

In that list the ARP Omni 1/II and the Moog Opus 3 share the highest price, £400. Electronics & Music Maker’s secondhand guide of June 1986 put the Omni at £200 or so, and called it ARP’s first attempt to break into the polysynth market. In 1993 Music Technology gave a target price of £100 to £150.

Musicians who used the ARP Omni

The accounts below come from interviews in which the players describe the Omni themselves, and each names the source.

Joy Division and New Order. In Electronics & Music Maker in March 1985, Bernard Sumner, called Barney in the interview, said the keyboards on Closer were a Pro One, a Powertran Transcendent 2000 and an ARP Omni, “in fact, mostly the Omni.” He described running it through a graphic equaliser and a Marshall Time Modulator. Later in the same interview Peter Hook says all their gear was stolen, and Sumner says they bought an ARP Quadra to replace the Omni. Peter Hook told International Musician in October 1985 that they used the Omni after their first synth and on some New Order material too. The Pro One has its own entry, the Sequential Circuits Pro One.

Bill Nelson. In November 1982 Bill Nelson told Electronics & Music Maker that he had owned an ARP Omni for a long time, and in August 1983 he said an ARP Omni string machine was on some tracks of Chimera.

Journey. In Mix magazine’s 2007 Classic Tracks article on Don’t Stop Believin’, Jonathan Cain says he played a Steinway and an ARP Omni on the song, the Omni for the short stabs, and that he had the Omni from his time in The Babys. In the same article the album’s co-producer and engineer, Kevin Elson, remembers the album’s keyboard parts as a Roland Jupiter and a Prophet.

Named by ARP. ARP’s own newsletter reported in August 1977 that Kerry Livgren and Steve Walsh of Kansas each used an Omni and that Tom Coster of Santana had added one, and in an early 1977 issue that Al Kooper was back on stage with one. These are ARP’s promotional reports. For the other names in later lists, including Music Technology’s 1993 list of users, I didn’t find interviews, so they aren’t covered here.

ARP Omni plugin: Full Bucket Music Oxid

Full Bucket Music’s Oxid is a software instrument that simulates the ARP Omni-2. Its maker lists Windows formats VST2, VST3, CLAP and AAX, and macOS formats VST2, VST3, CLAP, AU and AAX. It has 64 voices, string and synthesizer sections, and additional phaser and delay effects. Version 1.0.4 is dated 11 February 2026, and Full Bucket says the plug-ins on its site are freely available. The VST entry explains the plugin format. I found no hardware reissue or clone of the Omni from any maker.

ARP Omni demo videos

The first video below shows an Omni 1 and the second an Omni-2. Both come from the YouTube channel Synthchaser, which also sells restored Omnis according to its video descriptions.

Synthchaser #031, ARP Omni 1 Demonstration, by the YouTube channel Synthchaser, published in October 2016, about 12 minutes.
Synthchaser #053, ARP Omni 2 Demonstration, by the same channel, published in March 2017, about 14 minutes.

ARP Omni manuals and documentation

The specs on this page come from two ARP service manuals: the ARP OMNI Model 2480 Service Manual, document 90020000, dated February 1977, and the ARP OMNI-2 Service Manual for models 2471, 2472, 2473 and 2475, document 90026, dated July 1978. Scans of both circulate in online archives, but ARP marked them confidential and proprietary, and no rights holder offers them, so I don’t link to them. I didn’t find the owner’s manuals on any official site.

ARP’s own newsletters are on the Internet Archive, including the 1976 issue that announced the Omni. The magazine reviews and interviews cited here are on mu:zines. I found no photo of an Omni with a clear licence, so this page has no image of the instrument.

ARP Omni price and availability

The Omni and Omni-2 are discontinued and sell used. On 10 November 2026, viewed from Berlin, Reverb showed Used estimate unavailable on both product pages. The Omni page lists 6 dated sales, and the Omni-2 page lists 1.

Dated Reverb sales of the ARP Omni and Omni-2, newest first
Bar length = sale price on a scale of €0 to €2,000, with Reverb’s condition grade. Green = Omni, blue = Omni-2. Excludes shipping and tax.
Omni, 1 Aug 2026, Very Good€1,250
Omni, 26 Apr 2024, Good€700
Omni, 31 Jan 2023, Very Good€1,700
Omni, 19 Jan 2022, Good€1,350
Omni, 16 Nov 2019, Very Good€1,650
Omni, 4 Aug 2019, Very Good€880
Omni-2, 15 May 2024, Very Good€1,550
All rows of the transaction tables on Reverb’s Omni page (6 sales) and Omni-2 page (1 sale), read on 10 November 2026 from Berlin.

The six Omni sales run from €700 in April 2024 to €1,700 in January 2023, and the newest was €1,250 in August 2026. The single Omni-2 sale was €1,550 in May 2024. On the same day the Omni page showed 2 listings, asking €2,999 plus €290 shipping and €2,802.50, and the Omni-2 page showed none. I opened neither listing, and asks are not sales.

Related gear and terms

For the basics behind the Omni, see analog synthesizers and sound synthesis. Other synthesizers with their own entries here include the Moog Prodigy and the Sequential Circuits Pro One, which Joy Division used alongside the Omni.

Frequently asked questions

When did the ARP Omni come out?

Korg’s ARP history and Music Technology’s 1993 guide give 1975. The earliest dated document I found is ARP’s newsletter Vol. 5 No. 2, copyright 1976, which reports the Omni introduced to dealers at a NAMM meeting in Chicago. Korg dates the Omni-2 to 1977; its service manual is dated July 1978.

What is the difference between the ARP Omni and the Omni-2?

Both use the same 49-note divide-down tone generator, string phasers and 24 dB filter. The Omni-2 adds a preset bass synth with a Staccato switch, a separate bass output, a Single Trigger switch and two gate outputs. It has a steel case and weighs 39.5 lb against 33 lb.

Is the ARP Omni fully polyphonic?

Its string and synth sections sound every key held, because each of the 49 keys gets its own pitch from the dividers and its own gate. In the synth section all keys share one filter, one amplifier and one ADSR envelope, the strings share one amplifier, and the lowest cello and bass voices are monophonic.

Is the ARP Omni analog?

Mostly. Its pitches come from digital frequency dividers driven by a 500 kHz master oscillator, but the waveshaping, the 4075 filter, the amplifiers, the envelope and the three delay-line phase shifters are analog circuits. The analog delay lines are clocked at typically 50 kHz.

How does the ARP Omni’s string sound work?

The gated sawtooth tones pass through three parallel phase shifters. Each is an analog delay line whose delay, up to 0.8 milliseconds, is moved by its own low-frequency oscillator, and the three outputs are summed. ARP’s 1976 newsletter called the process asynchronous phase modulation.

What filter does the ARP Omni use?

The synth section uses one 4075 low-pass voltage-controlled filter with a slope of 24 dB per octave and adjustable resonance, shared by all keys. An ADSR envelope, an LFO of about 0.1 to 20 Hz and a pedal or external voltage can move its cutoff.

Who used the ARP Omni?

Bernard Sumner told Electronics & Music Maker in 1985 that the keyboards on Joy Division’s Closer were mostly the Omni. Bill Nelson said in 1983 that an Omni is on some tracks of Chimera, and Jonathan Cain says he played an Omni on Journey’s Don’t Stop Believin’. ARP’s newsletter named Kansas and Santana players in 1977.

Is there an ARP Omni plugin?

Yes. Full Bucket Music’s Oxid simulates the ARP Omni-2 for Windows and macOS in formats including VST3, AU and CLAP. Version 1.0.4 is dated 11 February 2026, it offers 64 voices and added phaser and delay effects, and the maker says its plug-ins are freely available.

How much did the ARP Omni cost new?

Contemporary Keyboard gave a list price of $2,250 in its November/December 1976 issue, and Synapse quoted $2,395, both as transcribed by the Retro Synth Ads blog. Music Technology gave £1,200 as the original UK price. ARP’s newsletter said it cost about half as much as other polyphonic keyboards.

How much is a used ARP Omni worth?

On 10 November 2026, viewed from Berlin, Reverb gave no used estimate. Its six dated Omni sales from 2019 to 2026 ranged from €700 to €1,700, the newest at €1,250 in August 2026, and its one Omni-2 sale was €1,550. Prices exclude shipping and tax.

Get free sounds in your inbox

New free presets and packs, the day they drop. Plus production tips and early access to paid releases.

Share this with a producer friend, or DM me @iamdreyandersson

Picture of Drey Andersson

Drey Andersson

Drey Andersson is a Berlin-based music producer and sound designer with over 20 years behind the desk. He co-produced Shekhinah's Different (SAMA award, RiSA Gold), won the Beatleague Beat Battle in Berlin, and built a 100K+ community around sound design and synthesis. He co-founded the Berlin producer collective Beat Unit and shares his sounds through his own Serum banks and free downloads.

Want the full toolkit?

My full Serum banks go deeper: hundreds of presets, custom wavetables from real vintage gear, and the exact sounds I use on my own productions.